Ionic liquid-based microemulsions were prepared to be used as eco-friendly fuel. The new ionic liquids were synthesized depending on castor oil as a renewable material. Castor oil contains a considerable amount of ricinoleic acid, which was easily converted into ionic liquids through an amidation process and quaternization as indicated in Scheme 1. The ricinoleic acid composition comprises a long hydrocarbon chain and polar hydroxyl carboxyl groups, making it an amphiphilic compound. The new ionic liquids were employed as emulsifiers to disperse ethanol within the diesel fuel. As a result, the prepared fuel samples combine the advantages of green ionic liquids and microemulsion properties. Ionic liquids that come from organic materials often have minimal toxicity and acceptable compatibility with other solvents41.Scheme 1:Synthesis of the ionic liquids (IL-1 & IL-2).During the formation of the microemulsion, emulsifiers assist in the expansion of the interface. Additionally, it can surround the ethanol particles that are broken down and dispersed in diesel, which stabilizes the dispersed phase in the continuous phase and increases the homogeneity of the microemulsion. Additionally, the emulsifier has an amphipathic effect that restricts and inhibits droplet agglomeration42.Spectroscopic characterization for the synthesized ionic liquids1H-NMR, 400 MHZ, DMSO-d6 (ppm) of ricinoleic acid (1) presented at chemical shifts: 0.94–0.97 (t, 3H, CH3–(CH2)4–), 1.23 (t, 8H, CH3–(CH2)4–), 1.26 (t, 8H, CH==CH–CH2–(CH2)4–), 1.33 (q, 2H, CH3–(CH2)4– CH2), 1.96 (q, 2H, CH==CH–CH2–(CH2)4–), 2.01 (1H, OH), 2.26–2.29 (t, 2H, HO–CH–CH2–CH=CH), 3.29 (2H, CH2–CO), 3.41–3.42 (m, 1H, HO–CH–CH2–CH=CH), 5.35–5.39 (dd, 2H, CH==CH) and 11 (s, 1H, –CO–OH). FTIR (cm−1) shows a broad band at 3459 cm−1 (–OH, stretching). The peak at 3008 cm−1 corresponds to the =C–H stretching. The asymmetric and symmetric C–H (methylene and methyl groups) stretching are represented by the peaks at 2927 and 2857 cm−1, respectively. The bands at 1740 cm−1, 1457, 726 are attributed to (C=O acid, stretching), (–CH2–, bending), and (cis alkene), respectively.1H-NMR, 400 MHZ, DMSO-d6 (ppm) of 12-hydroxy-N, N-bis(2-hydroxyethyl)octadec-9-enamide (2) presented at chemical shifts: 0.94–0.97 (t, 3H, CH3–(CH2)4–), 1.23 (t, 8H, CH3–(CH2)4–), 1.25 (t, 8H, CH==CH–CH2–(CH2)4–), 1.35 (q, 2H, CH3–(CH2)4–CH2), 1.96 (q, 2H, CH=CH–CH2–(CH2)4–), 2.00 (3H, 3OH), 2.26–2.28 (t, 2H, HO–CH–CH2–CH=CH), 3.31 (2H, CH2–CO–N), 3.40 (m, 1H, HO–CH–CH2–CH=CH), 3.43–3.46 (t, 4H, CH2–N–CH2), 4.01–4.04 (q, 4H, N–CH2–CH2–OH) and 5.33–5.37 (dd, 2H, CH=CH). FTIR (cm−1) shows a broad band at 3371 cm−1 (–OH, stretching). The asymmetric and symmetric C–H (methylene and methyl groups) stretching are represented by the peaks at 2926 and 2857 cm−1, respectively. The bands at 1620 cm−1, 1459, 1057, 719 are attributed to (C=O amide, stretching), (–CH2–, bending), (–C–N) and (cis alkene), respectively.1H-NMR, 400 MHZ, DMSO-d6 (ppm) of IL-1 (Fig. 1a,b) presented at chemical shifts: 0.84–0.87 (t, 3H, CH3–(CH2)4–), 1.137 (t, 8H, CH3–(CH2)4–), 1.15 (t, 8H, CH==CH–CH2–(CH2)4–), 1.19 (q, 2H, CH3–(CH2)4– CH2), 1.33–1.34 (t, 3H, CH3– CH2–O–CO), 1.49–1.52 (m, 2H, CH2– CH2–CO–N+), 1.95 (3H, 3OH), 2.05–2.10 (q, 2H, CH==CH–CH2–(CH2)4–), 2.24–2.27 (t, 2H, HO–CH–CH2–CH==CH), 3.34 (2H, CH2– CH2–CO–N+), 3.40–3.41 (m, 1H, HO–CH–CH2–CH==CH), 3.45–3.49 (t, 4H, CH2-N+– CH2), 4.01–4.06 (q, 4H, +N–CH2–CH2–OH), 4.44 (2H, CH3– CH2–O–CO) and 5.35–5.39 (dd, 2H, CH==CH). FTIR (cm−1) shows a broad band at 3351 cm−1 (–OH, stretching). The asymmetric and symmetric C–H (methylene and methyl groups) stretching are represented by the peaks at 2928 and 2857 cm−1, respectively. The bands at 1737 cm−1, 1660, 1446, 1067, 728 are attributed to (C=O ester, stretching), (C=O amide, stretching), (–CH2–, bending), (C–N stretching) and (cis alkene), respectively.Figure 1:1H-NMR Chemical structure spectroscopic characterization of IL-1.1H-NMR, 400 MHZ, DMSO-d6 (ppm) of IL-2 (Fig. 2a,b) presented at chemical shifts: 0.83–0.87 (t, 3H, CH3–(CH2)4–), 1.15 (t, 8H, CH3–(CH2)4–), 1.17 (t, 6H, CH==CH–CH2– CH2– (CH2)3–), 1.18 (2H, CH==CH–CH2–CH2–(CH2)3–), 1.33 (2H, CH3–(CH2)4– CH2), 1.49–1.52 (m, 2H, CH2– CH2–CO–N+), 1.95–1.98 (3H, 3OH), 2.07–2.09 (q, 2H, CH==CH–CH2–(CH2)4–), 2.23–2.26 (t, 2H, HO–CH–CH2–CH=CH), 3.32 (2H, CH2– CH2–CO–N+), 3.40–3.41 (m, 1H, HO–CH–CH2–CH==CH), 3.49–3.51 (t, 4H, CH2–N+– CH2), 4.01–4.06 (q, 4H, +N–CH2–CH2–OH), 4.34–4.35 (2H, N+– CH2–Ph), 5.35–5.39 (dd, 2H, CH=CH) and 7.30–7.35 (Ar H). FTIR (cm−1) shows a broad band at 3324 cm−1 (–OH, stretching). The peak at 3010 cm−1 corresponds to the aromatic = C–H stretching. The asymmetric and symmetric C-H (methylene and methyl groups) stretching are represented by the peaks at 2926 and 2856 cm−1, respectively. The bands at 1663 cm−1, 1607, 1462, 1058, 721 are attributed to (C=O amide, stretching), (–C=C–, stretching), (–CH2–, bending), (C–N stretching) and (cis alkene), respectively.Figure 2:1H-NMR Chemical structure spectroscopic characterization of IL-2.Ternary phase diagramFigure 3 illustrates the phase diagram of room-temperature microemulsion systems made up of ethanol, 1-butanol as a co-surfactant, and diesel/synthesized ionic liquids (IL-1 & IL-2) (4:1). Different proportions of nonpolar and polar phases were mixed to determine the microemulsion area. The visual method used to identify the phase change is one of the most crucial aspects of microemulsion preparation. The dispersion of ethanol in diesel phase was studied at ratios 5% ± 2.5%. It was observed that the microemulsion area in case of using IL-1 as emulsifier is started from (2.5% E, 14.5% B and 83% O + IL-1) to (7.1% E, 56.5% B and 36.4% O + IL-1) while the microemulsion area in case of using IL-2 as emulsifier is started from (2.5% E, 12% B and 86.5% O + IL-2) to (5% E, 63.7% B and 31.3% O + IL-2). It was noticed from the ternary phase diagram that the microemulsion area in case of using IL-1 is larger than the microemulsion area in case of using IL-2. As the percentage of B increases in the microemulsion sample containing IL-1, the microemulsion area slightly increases while in case of IL-2, the microemulsion area is nearly constant.Figure 3Ternary phase diagram of diesel/ionic liquid (O + IL), ethanol (E) and 1-butanol (B) at room temperature.Ethanol solubilization in microemulsionAs shown in Fig. 4, the amount of cosurfactant and ionic liquid is necessary for the efficient solubilization of ethanol in the microemulsion. The synthesized ionic liquids (IL-1 & IL-2) have the ability to make ethanol being solubilized within the diesel fuel with the aid of 1-butanol. But, their ability on ethanol solubilization varies. The amount of (IL-1 + cosurfactant) needed to solubilize 2.5% ethanol is 0.76 while the amount of (IL-2 + cosurfactant) needed is 0.73 to solubilize the same percentage of ethanol. The IL-2 and IL-1 nearly have the same effect on ethanol solubilization at low percentages of ethanol (2.5–4.1%). The two ionic liquids need the same amount of cosurfactant to solubilize 4.1% ethanol. Nevertheless, higher than 4.1% ethanol, the IL-1 is more efficient than the IL-2 in making ethanol solubilized within the diesel phase at the same ratios of cosurfactant/ionic liquids. Moreover, it was observed that there is a gradual increase in the amount of ethanol solubilized (> 5%) with the rise in the amount of (IL-1 + cosurfactant), in the case of IL-2, the amount of ethanol solubilized (> 5%) is slightly increases (nearly constant) and higher amounts from (IL-2 + cosurfactant). The hydroxyl groups in the synthesized ILs allow the formation of hydrogen bonds with alcohols in microemulsion and the polarity of ILs increases, as a result, enhancing the solubilization of ethanol in diesel. Therefore, the IL-1 is more preferred to solubilize ethanol because it contains three hydroxyl groups besides more oxygen atoms that increase the ethanol solubilization.Figure 4The Effect of synthesized ionic liquids and cosurfactant on ethanol solubilization.The ethanol particle sizesUsing the dynamic light scattering (DLS) technique, the size of the ethanol particles scattered in the fuel microemulsion as well as their size distribution were determined. The size and size distribution of the ethanol particles used in microemulsions with IL-1 and IL-2 as emulsifiers are shown in Figs. 5 and 6, respectively and in Table 1. The ethanol particles were found to be small, ranging in size from 8 to 18.1 nm in all samples which aid in the stability of the prepared microemulsions. This is due to the presence of hydroxyl groups in the synthesized ILs, increasing their polarity. Therefore, IL can adsorb on the interface and surround the ethanol particles tightly that are broken down and dispersed in diesel, as a result, enhancing the ethanol/diesel miscibility and increasing the homogeneity of the microemulsion43. Moreover, the hydroxyl groups in ILs allow the formation of hydrogen bonds with alcohols in microemulsion. In addition, It was observed that the particle sizes of ethanol in the case of using IL-1 as an emulsifier are lower than those in the case of IL-2 as an emulsifier at the same conditions. The microemulsion sample m1(IL-1) has the minimum particle size (8nm) which is approximately half the size of m1(IL-2) under the same conditions (IL/diesel 26%). As the ionic liquid ratios decrease in the microemulsion samples, the ethanol particle sizes increase, which is shown clearly in IL-1 samples. It was concluded that the IL-1 is more effective than the IL-2 in reducing the ethanol particle size. In addition, the ethanol particle size and its size distribution were close to each other in case of IL-1 and IL-2 at (IL/diesel 0.65%).Figure 5Particle size distribution of ethanol in fuel microemulsions using IL-1 as emulsifier.Figure 6Particle size distribution of ethanol in fuel microemulsions using IL-2 as emulsifier.Table 1 The mean particle sizes for microemulsion samples.An increase in the percentage of diesel in the microemulsion samples means a decrease in the percentage of the ionic liquids (IL: diesel 26%, 13%, 0.87% & 0.65%). Table 2 shows the effect of Ionic liquids ratios on the ethanol particle size in microemulsion samples. It was observed that as the ratios of ionic liquids decrease in microemulsion (reduction ratio from 37 to 69%), the ethanol particle sizes increase (increasing ratio from 10 to 25% in case of IL-2 and from 48 to 150% in case of IL-1). Moreover, the effect of reducing the ratio of IL-2 on the particle size increases smoothly, while the effect of reducing the ratio of IL-1 has a clear effect on the increasing particle size.Table 2 The effect of Ionic liquids ratios on the ethanol particle size in microemulsion samples.Stability of the microemulsion samplesMaintaining minimal engine modifications is one of the primary objectives of using fuel blends in engines, requiring blend stability and the development of a single-phase liquid system. Emulsifiers build up at the phase contact to lessen interfacial tension44. Emulsifiers develop up at the phase and interact to lessen interfacial tension. Emulsifiers work by forming a physical barrier or an attractive force between the dispersed phase and the emulsion droplets, thereby reducing the energy required to break the droplets apart and prevent them from collecting45.The particle sizes of m1(IL-1) and m1(IL-2) samples were examined every week for three months. The microemulsion samples show significant stability as shown in Fig. 7. The particle size of the m1(IL-1) sample increases gradually until reaching the seventh week (8 nm). Its particle size was further measured after the seventh week and it was observed that it remained almost stable at 8 nm till reaching the twelfth week. The particle size of the m1(IL-2) sample reaches stability in the ninth week and remains stable at 14 nm till the twelfth week. Additionally, the samples were cooled up to − 10 °C and no phase separation was seen in the microemulsions, suggesting the development of stable microemulsion. Moreover, the prepared microemulsions stayed at our lab transparently for more than a year and no phase separation was observed. This proves the ability of the synthesized ionic liquids to enhance the microemulsion’s stability by keeping the ethanol particles dispersed in the diesel phase, as a result, enhancing the solubilization of ethanol.Figure 7The stability of particle sizes for the prepared microemulsions with time.The physicochemical parameters of the prepared microemulsionsThe fuel properties of the prepared microemulsions were measured and compared with the properties of the neat diesel and ASTM D975 standards. The viscosity of prepared samples was measured at different temperatures. Figure 8a,b shows the relation among the viscosity of the prepared samples, volume ratios of IL, and the temperature for IL1 and IL2 microemulsion samples, respectively.Figure 8the relation among the viscosity of the microemulsion samples, the weight ratios of ionic liquids and the temperature (a) IL-1 samples and (b) IL-2 samples.As the temperature rises, the prepared samples become less viscous. Moreover, as the volume ratio of ionic liquid increases in microemulsion, the viscosity increases. For m1(IL-1) sample (contain 20% of IL1), at 40 °C, the viscosity increases by 3.96% compared to the viscosity of diesel. The viscosities of all IL1 and IL2 samples are within the ASTM D975 limits (1.9–4.1 mm2/s at 40 °C). In addition, the viscosities of m3(IL-1), m4(IL-1), m3(IL-2) and m4(IL-2) samples are found to be very close to the viscosity of the neat diesel at different temperatures. The IL1 and IL2 microemulsion samples nearly have the same effect but the samples of IL1 are slightly more viscous than the samples of IL2.The Fig. 9a,b show the relation among the density of the microemulsion samples, the volume ratios of IL and the temperature for IL1 and IL2 microemulsion samples, respectively. The densities of the prepared samples were found to decrease with the increase in temperature and decrease in the volume ratio of IL. As the ratio of IL increases by 20%, the density increases nearly by 1.2%. Also, the microemulsion samples were found to have densities that were close to those of neat diesel at different temperatures. The density and kinematic viscosity values of the fuel would affect the atomization, pumping of fuel into an engine, and eventually the evaporation of the fuel in an engine46. These attributes need to be close in value to the neat diesel as a result.Figure 9The relation among the density of the microemulsion samples, the weight ratios of ionic liquids and the temperature (a) IL-1 samples and (b) IL-2 samples.In the current study, the cetane number is replaced by the cetane index (ASTM D976). As indicated in Table 3, the prepared microemulsion fuels met the ASTM D975 acceptable minimum specifications and their cetane index was slightly lower than that of diesel because of the presence of alcohols in the microemulsion samples. The ricinoleic acid molecule also contains a double bond and free hydroxyl group, which lowers the cetane number. As the branching and unsaturation increase, the cetane number decreases47. However, the microemulsion fuels’ lower cetane index suggested an ignition delay, they did not cause engine knock. Since alcohol has a lower heating value than diesel, the vapors that were produced had a lower peak temperature. In addition, the hydroxyl groups in the synthesized ionic liquids have higher ignitability, making it a possible option for use as emulsifiers and to improve ethanol/diesel microemulsion fuel.Table 3 Fuel properties measurements for the prepared microemulsions.One important property that is utilized to determine how much energy is produced when the fuel burns fully is its heating value. Results in Table 3 indicate that compared to diesel (45.6 MJ/kg), the heating values of the m1(IL-1), m1(IL-2), m4(IL-1) and m4(IL-2) microemulsion samples were slightly lower (41.17, 41.3 MJ/kg, 42.6 & 42.8, respectively). This is explained by the fact that these samples contained more oxygen, which naturally decreased their heating values. Moreover, the oxygen content (wt%) increased from 0% in pure diesel to 8.48% and 7.26% in microemulsion fuel after using IL-1 and IL-2, respectively, which enhance the complete combustion, as a result, reduce harmful emissions. Also, the sulfur ratio is decreased from 2 to 1.23%. Thus, microemulsion fuels are regarded as ecofriendly fuels.An optical indicator of a substance’s ability to bend light beams is called its refractive index. The refractive index values of the microemulsions prove the transparency of the samples. Because ionic liquids and cosurfactant are present, microemulsions appear transparent or translucent yellow in colour. This illustrates how the microemulsion has very little scattering and low refractive index and is nearly transparent in the visible spectrum.The minimum temperature at which wax starts to crystallize in fuels and gives them a hazy appearance is known as the cloud point. Since solidified waxes can clog engine fuel filters and injectors, the fuel’s cloud point needs to be low for proper operation48. The lowest temperature restrictions for cloud point are not specified by ASTM D975, however according to IS 1460, they should be 3 °C for winter fuels and 15 °C for summer fuels. The microemulsion samples showed lower cloud points compared to diesel fuel due to the unsaturated fatty chain in the synthesized ionic liquids which has lower melting points than the saturated fatty chain indicated working without cold starts problems49. In addition, introducing low-cloud-point chemicals, such as 1-butanol and ethanol, improved the system’s cold flow characteristics.The amount of free fatty acids in the fuel sample is indicated by the acid value. The engine’s fuel supply system corrodes when the acidity number is high50. The acid values for the prepared samples were found to be within the permitted level as indicated in Table 3. Both EN14214 and ASTM-D6751 standard fuels have an acid value of 0.50 mg KOH/g or less.The used castor oil has acid value of 2.8 mg KOH/g and the process of hydrolyzing it to extract ricinoleic acid helps in lowering the acid value to use it as good raw material for the synthesis of ionic liquids and the preparation of microemulsions.the water content values of the prepared samples (0.15%, 0.16%, 0.18%, and 0.181% for m1(IL-1), m1(IL-2), m4(IL-1) and m4(IL-2), respectively) are higher than the water content of diesel fuel (0.04%). It follows that the microemulsion fuel’s water content is primarily derived from the ethanol that makes up its composition.Flash point is an important property for the storage and handling of combustible materials. It measures the degree of inflammability or the extent of catching fire easily from the fuel51. The prepared samples show higher flash points (61, 60, 59, 57 °C for m1(IL-1), m1(IL-2), m4(IL-1), and m4(IL-2), respectively) compared to diesel (56 °C) and ASTM requirements. The increase in flash points may be due to the addition of the synthesized ionic liquids which are derived from the castor oil (less volatile and has a high flash point of 230 °C) to the microemulsion samples. Consequently, the prepared microemulsions have improved stability with fire compared to the neat diesel, making them safer.
